Amada Equipment Financing:
Press Brakes, Fiber Lasers and AMNC 3i Machines.

Amada is one of the anchor names in sheet metal fabrication. Its press brakes bend the parts, its fiber lasers cut the blanks and its AMNC 3i control ties a shop floor into a single operating language. For a fabricator that standardizes on the brand, that consistency is the whole point. It also makes the capital decision larger, because a bending and cutting cell built around one manufacturer is a coordinated purchase rather than a string of one-off buys. This page walks through the Amada lines that fabricators finance most often, what the control platform means for uptime and resale and how iLease Capital structures the transaction so the equipment can pay for itself while the payments run.

We finance Amada equipment new and used, single machines and full cells, for deals up to $5 million plus. Everything below is written to help you plan the purchase, not to sell you a stock number.

Why fabricators standardize on Amada

A modern fabrication shop lives on two operations: cutting flat blanks and bending them into finished geometry. Amada is one of the few builders that supplies both halves at a high level, which is why so many job shops and OEM suppliers run an all-Amada floor. When the laser, the press brake and the software all speak the same control language, programming time drops, operator cross-training gets simpler and the cell behaves as one system instead of three vendors pointing at each other.

That coherence carries a real financial consequence. Amada machines hold their value well on the used market because the installed base is large, parts and service are widely available and buyers trust the brand. Strong resale matters to a lender because the equipment is the collateral. When a machine retains value, the financing behind it is easier to structure and the terms tend to be friendlier. It also protects you, the owner, because a machine that sells well is a machine you can exit or trade up without taking a bath.

The AMNC 3i control platform

Before the individual lines, it helps to understand the control, because it is the thread that runs through current Amada equipment. AMNC 3i stands for intelligent, interactive and integrated. It presents an 18.5 inch multi-touch touchscreen with a smartphone-style interface, so an operator who has never run the machine can enter a job and start producing quickly. Newer press brakes add a Lite mode that strips the screen down to the essentials for straightforward parts.

The control does more than look modern. On the press brake side it runs real-time closed-loop angle correction. The machine measures the bend as it happens, feeds the result back to the controller and, if springback has pulled the angle off target, applies a micrometer-level incremental force until the measured angle matches the programmed angle. On the cutting side the same control platform manages the laser and its automation. The practical result is faster setup, fewer scrapped parts and tighter communication between your CAM software and the machine. For financing, a common control across the floor is a quiet advantage, because it lowers training risk and keeps a used machine desirable to the next buyer.

Amada press brakes: HG, HRB and HFE

Press brakes are the bending workhorses, and Amada's current catalog centers on three families.

The HG series is the flagship down-acting line. It spans roughly 56 to 247 tons in the US range, with bend lengths from about 55 inches to 169 inches, and it is offered in hybrid drive configurations that pair speed with accuracy. Models are named by bed and tonnage code, so an HG 1303 or an HG 8025 tells you the capacity and length at a glance. The HG-ARs variant adds automated bending, and HG ATC builds add an automatic tool changer so the machine can reconfigure its tooling without an operator handling every station.

The HRB series is described by Amada as the latest evolution in hydraulic drive brakes. It combines a new frame design with the proven features of the earlier HFE3i platform, covers 50 to 220 tonnes and 2 to 4 meters and offers an increased open height up to 520 mm with a 250 mm stroke, which gives more clearance for parts with tall flanges. The hydraulic circuit runs on demand through an inverter, so the machine only draws power for the motion the bending cycle needs. That on-demand behavior trims energy cost over a long ownership window.

The HFE and HFE3i series rounds out the range with a wide spread from about 50 tons and 1.2 meters up to 400 tons and 6 meters. The HFE3i is the current AMNC 3i version, while plain HFE machines are common on the used market and remain productive brakes for shops that do not need the newest interface.

On used values, Amada brakes cover a broad ladder. Aggregated dealer data placed used Amada press brakes from roughly $5,099 to $199,999, with an average near $39,326 and a median around $26,000 as seen on 2026-09-12. Individual points fill that in: a 2000-era 8025NT was listed near $24,900, while a 2003 HFE-1003S with CNC control and crowning carried a $44,500 asking price. A newer 89 ton HG-8025 from 2015 was listed by a dealer, which shows late-model machines stay in circulation even when a specific unit sells before a price is published. The takeaway is that a used Amada brake is financeable across a wide range of budgets, and the exact structure follows the machine's year, tonnage, hours and control generation.

Amada lasers: ENSIS fiber, LCG fiber and legacy FO CO2

On the cutting side, the story of the last decade is the move from CO2 to fiber, and Amada's lineup shows that shift clearly.

The ENSIS series is the flagship fiber line, built around variable beam control that lets one machine cut thin and thick material well without swapping optics. The common workhorse is the ENSIS-3015 AJ (and the AJe update), where 3015 denotes a 3000 by 1500 mm sheet, the familiar 5 foot by 10 foot table. Power options run from 2 kW up to 15 kW, with 3 kW, 6 kW and 9 kW builds frequent in the field. Every current ENSIS runs the AMNC 3i control.

The LCG series is a high-speed fiber line, with the LCG-3015 AJ handling the same 60 by 120 inch sheet and offered in 2 kW, 3 kW and 6 kW builds. It is a strong fit for shops that want fiber throughput without the top-end ENSIS feature set.

The FO series is the legacy CO2 generation, sometimes called Flying Optic, typified by the FO-3015 and FO3015NT at 4000 W on a Fanuc 16i-L class control. These machines still cut, but they represent the pre-fiber era and their values reflect that.

Used laser values split sharply along the CO2 to fiber line, and that split is the single most important thing to understand before buying. A 2002 FO-3015 4 kW CO2 machine with dual tables was listed at just $13,900 as seen on 2026-09-12, while a low-hour 2019 ENSIS 3015 AJ 3 kW machine with only 194 beam-on hours carried a $499,900 asking price and a 2018 ENSIS 3015 AJ was listed by a dealer at $700,000. A broad aggregate of Amada laser listings sat between about $25,000 and $39,990 with an average near $32,495, but that figure skews heavily toward older CO2 and low-power units and should not be read as the price of a recent fiber machine. LCG used pricing tracks between the legacy CO2 floor and the ENSIS band, positioned as a mid-tier fiber option, though a precise asking-price benchmark was not available at the time of review. The practical planning point is simple: a used CO2 Amada is cheap to buy and expensive to run, while a used fiber Amada costs far more up front and pays it back in speed, gas cost and material range. Financing lets you choose on production economics rather than on the size of the check.

Why the CO2-to-fiber shift matters for your loan

The value gap between an FO CO2 machine and an ENSIS or LCG fiber machine is not a rounding error, it is the difference between a five-figure and a six-figure asset. That gap shapes the financing in two ways.

First, collateral value. A recent fiber laser is a strong, liquid asset that supports a clean structure and competitive terms. An aging CO2 machine is worth far less, so a lender will look harder at the rest of the deal and may weight your business cash flow more than the equipment. Neither is a problem, they are just different conversations.

Second, total cost of ownership. Fiber cutting uses dramatically less consumable gas and electricity than CO2 and cuts reflective materials CO2 struggles with. When we structure a fiber laser purchase, the monthly payment is often close to or below the operating savings versus the old machine it replaces. That is the case we help you build, so the equipment funds a meaningful share of its own cost while you own it.

How iLease structures Amada financing

We finance Amada equipment for deals up to $5 million plus, which comfortably covers a single used brake, a new ENSIS cell or a coordinated laser-and-brake buildout, with no minimum floor on the transaction. Common structures include straight equipment finance agreements, capital leases with a $1 buyout for shops that intend to keep the machine long term and fair-market-value leases for shops that want to refresh technology on a cycle, which is a real consideration given how fast fiber laser power and control features move.

Because Amada machines hold value, used purchases from a dealer, an auction or a private seller are financeable, not just new orders through a distributor. We can also fold in freight, rigging, installation and tooling so the amount financed reflects the true cost of getting the machine cutting or bending on your floor rather than just the base machine price.

Credit review starts with a soft inquiry, which does not affect your business or personal credit score. A hard pull may come only at final approval once you have a machine and terms you want to move on. That sequence lets you shop structures and compare payments early without a paper trail of inquiries following you around.

Approvals are driven by time in business, cash flow and the equipment itself rather than by a single credit score, so established fabricators and newer shops both have a path. We work with a range of lenders and funding partners, which means we can match the profile of your business and the specific Amada machine to the source most likely to approve it on strong terms.

Getting started

The fastest way to a real number is to tell us the exact Amada model you are targeting, whether it is new or used, the year and hours if used and roughly what your shop's revenue and time in business look like. From there we can put an indicative structure and payment in front of you quickly, then firm it up once you have selected a machine. Call (866) 545-3273 with those details and we can start that conversation today.

Ready to finance your Amada equipment?

Tell us the model you are targeting and we will build a structure around it. Call (866) 545-3273, start your application at ileasecapital.com/apply, it takes about three minutes and there's no hard credit pull, or reach the team through /contact. We will begin with a soft inquiry that does not affect your credit, then firm up terms once you have your machine selected.

Frequently asked questions